COMPLIANCESviFrance and Peru onlyThis unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2
COMPLIANCESvii• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité
COMPLIANCESviiiBitte unbedingt vor dem Einbauen des RPU die folgenden Sicherheitsanweisungen durchlesen:WARNUNG: Die Installation und der Ausbau des G
COMPLIANCESixWarnings and Cautionary MessagesWar nings (in German)Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden: Schweiz D
COMPLIANCESxEnvironmental StatementThe manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire pro
COMPLIANCESxiSafety ComplianceWarning: Fiber Optic Port SafetyAvertissment: Ports pour fibres optiques - sécurité sur le plan optiqueWarnhinweis: Fase
COMPLIANCESxii
vii TABLE OF CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Features and Benefits . . . . . . . . . . .
viii
FEATURES AND BENEFITS1INTRODUCTIONThe EZ Switch™ 10/100/1000, SMCGS16 and SMCGS24, are high-performance Gigabit Ethernet switches designed for delive
INTRODUCTION2Front Panel RJ-45 PortsThe EZ Switch 10/100/1000 features 16/24 1000BASE-T ports with RJ-45 connectors located on the front panel of the
REAR PANEL3SMCGS16SMCGS24Rear PanelThe AC power connector is located on the rear panel of the switch.
INSTALLING THE SWITCH4INSTALLING THE SWITCHBefore installing the switch, verify that you have all the items listed under “Package Contents.” Note that
INSTRUCTIONS5• There should be adequate space (approximately two inches) on all sides for proper air flow.• Make sure twisted-pair cable is always rou
INSTALLING THE SWITCH6Note: If an attached device does not support auto-negotiation, the data rate will be sensed automatically and the communication
INSTRUCTIONS7APPLICATION EXAMPLEA typical application for the SMCGS16 is illustrated below.EZ Switch 10/100/1000SMCGS16ServerSMC-EZ109DTWorkstationsLA
TROUBLESHOOTING8TROUBLESHOOTINGDiagnosing Switch Indicators1. SymptomPower LED does not light after power on.Probable Causes• AC power cord may be def
CABLE SPECIFICATIONS9CABLESCable Specifications10BASE-T/100BASE-TX Pin AssignmentsCaution: DO NOT plug a phone jack connector into any RJ-45 port. Use
CABLES10The table below shows the 10BASE-T/100BASE-TX MDI-X and MDI port pinouts.1000BASE-T Pin AssignmentsThe table below shows the 1000BASE-T MDI an
1000BASE-T CABLE REQUIREMENTS111000BASE-T Cable RequirementsAll Category 5 UTP cables that are used for 100BASE-TX connections should also work for 10
38 TeslaIrvine, CA 92618Phone: (949) 679-8000EZ Switch 10/100/1000User GuideFrom SMC’s EZ line of low-cost workgroup LAN solutionsApril 2005Pub. # 150
PRODUCT SPECIFICATIONS12PRODUCT SPECIFICATIONSEZ Switch 10/100/1000Standards ConformanceIEEE 802.3-2002Ethernet, Fast Ethernet, Gigabit EthernetFull-d
EZ SWITCH 10/100/100013WeightSMCGS16: 2.0 kg (4.04 lbs)SMCGS24: 2.2 kg (4.85 lbs)MAC Address Table8 K entriesMemory BufferSMCGS16: 272 Kbits on-chip f
PRODUCT SPECIFICATIONS14
FOR TECHNICAL SUPPORT, CALL:From U.S.A. and Canada (24 hours a day, 7 days a week)(800) SMC-4-YOU; Phn:(949) 679-8000; Fax: (949) 679-1481From Europe
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, n
iLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un
LIMITED WARRANTYiiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT O
COMPLIANCESiiiCOMPLIANCESFCC - Class AThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Par
COMPLIANCESivIndustry Canada - Class AThis digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as se
COMPLIANCESvPlease read the following safety information carefully before installing the Switch:WARNING: Installation and removal of the unit must be
Comments to this Manuals