SMC Networks SMC-EZ1024DT User Manual

EZ Switch 10/1008-Port Fast Ethernet Switch 8 auto-MDI/MDI-X ports—connect to PCs or other switches or hubs One Gigabit port for high-speed uplink

COMPLIANCESiv

vTABLE OF CONTENTSAbout the EZ Switch 10/100 . . . . . . . . . . . . . . . . . .1Features and Benefits . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTSvi

1ABOUT THE EZ SWITCH 10/100ABOUT THEEZ SWITCH 10/100The EZ Switch 10/100 SMC-EZ109DT is an 8-port Fast Ethernet switch with one Gigabit uplink port. T

ABOUT THE EZ SWITCH 10/1002Features and Benefits◆ Auto configuration for MDI/MDI-X cable connection allows connections to servers, workstations, hubs

ABOUT THE EZ SWITCH 10/1003Front Panel LEDsThe front panel of the switch provides status LEDs for “at-a-glance” system monitoring. The following table

ABOUT THE EZ SWITCH 10/1004Rear PanelThe AC power receptacle is located on the rear panel of the switch.Gigabit Port LINK/ACTOff The port has not esta

INSTALLING THE SWITCH5INSTALLING THE SWITCHEquipment ChecklistAfter unpacking the EZ Switch 10/100, check the contents of the box to be sure you have

INSTALLING THE SWITCH6Make sure that a properly grounded power outlet is within 2.44 meters (8 feet) of the switch and is powered from an independent

INSTALLING THE SWITCH7Note: It is not necessary to power off the switch before connecting or disconnecting any UTP cables, as these actions will not d

INSTALLING THE SWITCH8Sample ApplicationsThis switch segments your network, significantly increasing both bandwidth and throughput. Any port on the sw

INSTALLING THE SWITCH9Gigabit Uplink Port - You can use the Gigabit port to support applications such as high-speed file servers, or for connecting to

TROUBLESHOOTING10TROUBLESHOOTING1. SymptomPower LED does not light after power on.Probable CausesPower outlet or power cord may be defective.Possible

CABLES11CABLESCABLE SPECIFICATIONsMaximum 10BASE-T, 100BASE-TX and 1000BASE-T Cable LengthCable Type Max. Length Connector10BASE-T Cat. 3, 4, 5 100-oh

CABLES12RJ-45 Connector Pin AssignmentsCaution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connec

CABLES131000BASE-T Pin AssignmentsThe table below shows the 1000BASE-T MDI and MDI-X port pinouts. These ports require that all four pairs of wires be

CABLES141000BASE-T Cable RequirementsAll Category 5 UTP cables that are used for 100BASE-TX connections should also work for 1000BASE-T, providing tha

CABLES15Adjusting Existing Category 5 Cabling to Run 1000BASE-TIf your existing Category 5 installation does not meet one of the test parameters for 1

SPECIFICATIONS16SPECIFICATIONSAccess MethodCSMA/CDPorts8 10BASE-T/100BASE-TX, with auto-negotiation1 100BASE-TX/1000BASE-T with auto-negotiationNetwor

SPECIFICATIONS17Weight 0.85 kg (1.87 lbs)TemperatureOperating: 0 to 40 °C (32 to 104 °F)Storage: -40 to 85 °C (-40 to 185 °F)Humidity5% to 95% non-con

6 HughesIrvine, CA 92618Phone: (949) 707-2400EZ Switch 10/100User GuideFrom SMC’s EZ line of low-cost workgroup LAN solutionsMay 2001Pub. # 150524-R01

SPECIFICATIONS18

6 HughesIrvine, CA 92618Phone: (949) 707-2400FOR TECHNICAL SUPPORT, CALL:From U.S.A. and Canada (24 hours, 7 days a week)(800) SMC-4-YOU; (949) 707-24

CopyrightInformation furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for i

LIMITED WARRANTYLimited WarrantyLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship an

LIMITED WARRANTYOF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WA

iCOMPLIANCESFCC Class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rule

COMPLIANCESiiIndustry Canada - Class AThis digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as se

COMPLIANCESiiiWichtige Sicherheitshinweise (Germany)1. Bitte lesen Sie diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung für den späteren